Felling OEM Parts

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

7K Jack, Top Wind with 4 Bolt Plate, Will come unpainted

25K Jost Drop Foot 2 Speed Jack with Plate welded on

Drop Deck Trailer 12K Jack, Side Pin Side Wind, With Plate

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

7K Jack, Top Wind with 4 Bolt Plate, Will come unpainted

Felling Mfg. Component - RAMP SPRING 1" SHAFT LH

Felling Mfg. Component - RAMP SPRING 1" SHAFT RH

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

7K Jack, Top Wind with 4 Bolt Plate, Will come unpainted

Drop Deck Trailer 12K Jack, Side Pin Side Wind, With Plate

Hydraulic Cushion Cylinder for Drop Deck Tilt Trailers, They have port inside that slows the flow of fluid Back and Forth, They are filled with Aut...

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

25K Jost Drop Foot 2 Speed Jack with Plate welded on

Hydraulic Cushion Cylinder for Drop Deck Tilt Trailers, They have port inside that slows the flow of fluid Back and Forth, They are filled with Aut...

Inner Bearing fits 25520 Race, fits most 6-8K axles as an inner bearing, does also fit a 9-10k general duty axle outer bearing

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

25K Jost Drop Foot 2 Speed Jack with Plate welded on

Hydraulic Cushion Cylinder for Drop Deck Tilt Trailers, They have port inside that slows the flow of fluid Back and Forth, They are filled with Aut...

15' extension replacement for Felling Trailers after 2015. It will fit DC4309 Pumps and is for a Power Up and Down Model. This new option allows yo...

Hydraulic Cushion Cylinder for Drop Deck Tilt Trailers, They have port inside that slows the flow of fluid Back and Forth, They are filled with Aut...

3/4" RED BULLET LIGHT WITH GROMMET PREVIOUSLY WAS PART #1050035

Heavy Duty Draw Latch For Tilt Trailers, There Is Also One With A 90 Deg Handle Part# 005514

Hopkins Engager System. These are for our new harness's to plug right in but you can just clip the end off to make it work with older trailers. Thi...

This is the replacement front main harness for drop deck and some deck over Trailers. It is 82" long and will plug into existing harnesses after Ap...

15' extension replacement for Felling Trailers after 2015. It will fit DC4309 Pumps and is for a Power Up and Down Model. This new option allows yo...

Felling Mfg. Component - RAMP SPRING 1" SHAFT LH

Felling Mfg. Component - RAMP SPRING 1" SHAFT RH

Hydraulic Cushion Cylinder for Drop Deck Tilt Trailers, They have port inside that slows the flow of fluid Back and Forth, They are filled with Aut...

3/4" RED BULLET LIGHT WITH GROMMET PREVIOUSLY WAS PART #1050035

The regular chains have been replaced by yellow straps that go around the shocks that Limit the Travel of Suspension

2-1/2" Round Grommet - Flush Mount - Open Back

3/4" RED BULLET LIGHT WITH GROMMET PREVIOUSLY WAS PART #1050035

The regular chains have been replaced by yellow straps that go around the shocks that Limit the Travel of Suspension

2-1/2" Round Grommet - Flush Mount - Open Back

Air Tank 1488 Cubic Inch 9.5" Diameter